0

Seu carrinho
Seu carrinho está vazio.

Sub-total:
R$ 0,00
Realizar Pedido
DJI Osmo Pocket 3
IMAX GPS
NOVIDADES
OUTLET
UFQ Aviation
Drones
Aeromodelismo
Jatos
Helimodelismo
Nautimodelismo
Automodelismo
Tamiya
Tratores
Paramotor & Peças
Turbinas e Acessórios
Baterias e Conectores
Servos e Peças
Carregadores e Balanceadores
Radios TX/RX e Acessórios
Abastecimento
Brushless Motors
Autorama
Brushless ESC
Aerográfos
Cristais e Frequencia
Colas e Adesivos
Combustíveis e Óleos
Check Packs
Tacômetros
Termômetros
Starters de Partida
Simuladores
Modelos Plastimodelismo
Pipas Acrobáticas
Grife Hobby
Velas Glow e Gas Air/Heli
3D Metal Model Kits
PRO-MOUNTAIN
Ferramentas Gerais
Ferromodelismo
Motomodelismo
Carrinhos Hot Wheels
FPV Cameras
FPV Telemetria
FPV Goggles
AIRCRAFT ENGINE PARTS
AIRCRAFT ELECTRICAL PARTS
AIRCRAFT AIRFRAME PARTS
PILOT SUPPLIES
AVIONICS
INSTRUMENTS
GIFTS
PARAMOTOR & SKYDIVE
Aircraft Model
Boneca Baby Reborn
Gemini Jets
JC Wings
Metal Earth
Runway-24
Action Figures
Brinquedos

CORONA RX R820FA 8CH FUTABA FASST S-BUS COMPATIBLE MINI-FASST

Ref: 351669
Estoque: Disponível
R$ 257,31
Comprar
Product Description

Corona R820FA 2.4Ghz FASST Compatible S.BUS Mini Receiver for RC Drone 

Pack Included:

X 1 Piece Corona R820FA Rx

Specifications:

Operating Current: 50mA max Operating Voltage: 3.6 ~8.4V Latency: S.BUS mode:14mS at FASST multi-channel mode, 16mS @ FASST 7ch mode CPPM mode: 21mS @ FASST multi-channel mode, 24mS @ FASST 7ch mode Sensitivity: about -90dBm Weight: about 2g SIZE: L*W*H=30mm*14mm*3mm Output mode: S.BUS or CPPM can be selected

Bind procedure:

Turn on the FASST transmitter Connect the battery to the receiver while pressing receiver’s F/S button. The Dual-color LED’s continuous will cycle through the following: Red LED light (searching radio signal) Green LED light (acquired the radio signal) Red LED off (bind ok) Green LED flashes 10 times (ID store in memory) Green LED lights solid (normally operation)

Fail-safe setting:

TX-failsafe feature: This method is to set failsafe on the FASST transmitter (works on channel 3 only under FASST 7ch mode or on multiple-channels under FASST multi-channel mode) while the receiver is working on, just like the FUTABA receivers. Note: We highly recommend you set failsafe feature while flying your models. An example of a useful Failsafe setting would be to shut down the model’s throttle, so that it does not fly or drive away uncontrolled.

Output mode setting:

If your receiver has been linked with your transmitter, please power off your transmitter. When your receiver’s LED light red, push down and hold the button on your receiver for more than 6 seconds and not more than 10 seconds, release the button to see the green led flash, push down the button again right now, receiver get back to light red. Now the MODE status has changed between S.BUS output mode and CPPM(continuous PPM signal on one wire) mode. When green led flash low indicate S.BUS mode to CPPM mode, and green led flash fast indicate CPPM mode to S.BUS mode. And power on the receiver again to take new feature effect. Do not connect any servo directly to the RX, it maybe get abnormal action or get hot. LED status indicated under normal working status: RED LED GREEN LED Status on off No signal searched off solid Signal is very good

Escreva um comentário

Você deve acessar ou cadastrar-se para comentar.

Similares